Car doors and windows Opel Astra J (petrol)

Removal and installation of an upholstery of a forward door
You will need: screwdrivers with a flat and cross-shaped blade. 1. Disconnect the wire from the terminal «minus» battery. 2. Prying off the plug with a...

Front door glass replacement
You will need a flat blade screwdriver. 1. Remove the front door upholstery (see Removal and installation of an upholstery of a forward door ). 2. Pry off the...

Replacing the power window of the front door
The front door windows are electrically operated. This subsection describes only the removal and installation of the power window directly. Replacing the power...

Replacing the outside handle and front door lock switch
Replacing the outside handle and left door lock switch is shown. The handle and switch of the right door are replaced in the same way. You will need: TORX T20...

Replacement of the internal handle of a drive of the lock of a forward door
You will need: TORX T20 wrench, electric soldering iron. 1. Remove the front door upholstery (see Removal and installation of an upholstery of a forward door...

Replacing the front door lock
You will need: TORX T30 wrench, flat blade screwdriver. 1. Raise the glass to its highest position and remove the front door trim (see Removal and installation...

Replacing the front door opening limiter
You will need a socket «on 10». 1. Raise the glass to its highest position and remove the front door trim (see Removal and installation of an upholstery of a...

Removal and installation of a forward door
You will need: end head «on 10», flat blade screwdriver. 1. Disconnect the wire from the terminal «minus» battery. 2. Open the front door. 3. Turn out a bolt...

Removal and installation of an upholstery of a back door
You will need: screwdriver with a flat and Phillips blade. 1. Disconnect the wire from the terminal «minus» battery. 2. Prying off the plug with a...

Rear door glass replacement
You will need: end head «on 10», TORX T20 wrench, flat and Phillips screwdrivers. 1. Remove the back door upholstery (see Removal and installation of an...

Replacing the power window rear door
The rear door windows are electrically operated. This subsection describes only the removal and installation of the power window directly. Replacing the power...

Rear Door Exterior Handle Replacement
Replacing the outer handle of the left door is shown. The right door handle is replaced in the same way. You will need: TORX T20 wrench, flat blade...

Replacing the inner handle of the tailgate lock actuator
You will need an electric soldering iron. 1. Remove the back door upholstery (see Removal and installation of an upholstery of a back door ). 2. On the inside...

Replacing the rear door lock
You will need: TORX wrenches T20 and T30, flat blade screwdriver. 1. Raise the glass to its highest position and remove the tailgate upholstery (see Removal...

Replacing the tailgate opening limiter
The methods for replacing the rear door opening limiter are completely similar to the methods for replacing the front door limiter (see Replacing the front...

Removal and installation of a back door
Removal and installation of the rear door is completely similar to the removal and installation of the front door (see Removal and installation of a forward...

Replacing tailgate stops
You will need a flat blade screwdriver. 1. Open the tailgate and lock it in the open position (e.g. with a piece of wood of suitable length) or ask an...

Removal and installation of an upholstery of a door of a back
You will need: end head «on 7», flat blade screwdriver. 1. Open the tailgate. 2. Remove the trunk shelf cords from the holders. 3. Pry off the edge of the...

Removal and installation of an external lining of a door of a back
You will need: end head «on 10», flat blade screwdriver. 1. Disconnect the wire from the terminal «minus» battery. 2. Remove the lower part of the upholstery...

Replacing the tailgate lock
You will need a TORX T40 key. 1. Disconnect the wire from the terminal «minus» battery. 2. Remove the lower part of the upholstery of the tailgate (see Removal...

Removal and installation of a door of a back
You will need: end head «at 13», flat blade screwdriver. 1. Open the tailgate and lock it in the open position (e.g. with a piece of wood of suitable length)...

Removal and installation of a cover of the hatch of a bulk pipe of a fuel tank
No tool is required to remove the fuel tank filler cap. 1. Open the hatch cover of the fuel tank filler pipe, to do this, lightly press the left edge of the...

Removal and installation of the lock of a cover of the hatch of a bulk pipe of a fuel tank
You will need a flat blade screwdriver. 1. Remove the lining of the trunk on the right side in the direction of the car. 2. Press the latch of the block of the...

Replacement of the fixed glazing of the body
The windshield and tailgate windows are glued into the body and door openings, respectively. They are replaced by the same techniques, so the work is shown on...